PLA – UPS THREE PHASE, DOUBLE CONVERSION, SINE WAVE, form 10 to 200KVA
PLA is a true on-line UPS, double conversion technology with high efficiency. Input and Output voltages are three-phase. Rating power available from 10kVA to 200kVA. High performance and high efficiency with PF 0,9. PLA uses power modular technology and it works in redundance mode N+x. It is a flexible system, in fact is possible to add or remove power cabinets depending by the amount of load to supply. In this way it is possible to optimize the financial investments by escalating the configuration according to the real needs. PLA can be used for any kind of load: IT, AUTOMATIC MACHINE, DATA CENTER, HOSPITAL, INDUSTRY, etc. PLA can solve every kind of problems, such as blackouts, spikes, voltage disturbances, frequency disturbances, harmonic distortion (THD <2%) current noise, brownouts, surges, and so on. PLA series uses a Digital Signal Processor (DSP) control to increase the reliability, the efficiency, and for auto protection and auto diagnosis. PLA series keep input current balanced. No unbalance problems may occur during the operation.
MAIN FEATURES
- True On-line UPS input three-phase + N, output three-phase + N
- Switching time 0 ms
- Power factor 0,9 – (optional 0,8)
- LCD display
- Modular power from 10kVA to 200kVA
- DSP (Digital Signal Processor)
- Input Low distortion < 2%
- ECO mode function
Optional: SNMP, MODBUS, RELAY. Standard: USB port, RS485, EPO contact
MODULAR POWER TECHNOLOGY
Modular power technology used for PLA series is an easy “Parallel concept”.
PLA series has an intelligent sensor which automatically detects other UPSs with same power.
No settings via software, no parallel boards needed, UPS it is always ready and with a self test reset and adjust its
output power.
Parallel control cables are shielded with double isolation to avoid noise interference.
The cables are connected in ring mode, as shown in the picture below.
Ring connection is very reliable.
The parallel configuration guarantees an higher reliability than a single “full power” UPS. For making a correct
configuration it is important to meet the items written below:
1) Every UPS must have the same power and connected to the same by-pass line .
2) The electric cables (input, output, by-pass) must have the same length and same characteristic
| MODEL | PLA10 | PLA15 | PLA20 | PLA30 | PLA40 | PLA60 | |||
| Input | Power | 10KVA
9KW |
15KVA
13.5KW |
20KVA
18KW |
30KVA
27KW |
40KVA
36KW |
60KVA
54KW |
||
| No. of phases | 3 phase 4 wires + PE | ||||||||
| Rated voltage | 380/400/415Vac | ||||||||
| Voltage range | 208~478Vac | ||||||||
| Frequency range | 45-55Hz a 50Hz / 56-66Hz to 60Hz (auto sensing) | ||||||||
| Power factor | ≥0.99 | ||||||||
| THDi | ≤2%(100% non linear load) | ||||||||
| By-pass voltage range | Max voltage.: 220Vac:+25% (optional +5%,+10%,+15% ) 230Vac:+20% (optional +10%,+15% ) 240Vac:+15% (optional +10% ) |
||||||||
| Min voltage.: -45% (optional -20%、-30%) | |||||||||
| Frequency protection range: ±10% | |||||||||
| Generator input | Supported | ||||||||
| Output | No. of phases | 3 phase 4 wires + PE | |||||||
| Rated voltage | 380/400/415Vac | ||||||||
| Power factor | 0.9 | ||||||||
| Voltage accuracy | ±1% | ||||||||
| Frequency | Line | ±1%、±2%、±4%、±5%、±10% rated frequency (optional) | |||||||
| Battery | (50/60±0.1%)Hz | ||||||||
| Crest Factor | 3:1 | ||||||||
| THD | ≤1% linear load – ≤3% non linear load | ||||||||
| Efficiency | ≥96,5% | ≥97,5% | |||||||
| Battery | Quantity | Dynamic 16-18-20pcs (configurable) | |||||||
| Autonomy | 10’ standard with embedded battery | ||||||||
| Overload | Normal op.: 110% 60′ – 125% 10′ – 150% 1′ – >150% switch to bypass | ||||||||
| Self-check | Automatic self test at switch on | ||||||||
| Display | LCD: Voltage IN/OUT – Frequency IN/OUT – Load – Battery Voltage
Operating Temp. – Overload – Failure – Alarms |
||||||||
| Interface | USB – RS485 – Clean Contacts- Intelligent slot | ||||||||
| Communication | SNMP (optional) – MODBUS (optional) – RELAY card (optional) | ||||||||
| Operating temperature | Operating: 0° + 40° / Storage: -25° + 55° | ||||||||
| Dimensions (DxWxH) mm | 828x250x868 | 828x500x868 | |||||||
| Number of units | 1 | 2 | |||||||
| MODEL | PLA80 | PLA100 | PLA120 | PLA160 | PLA180 | PLA200 | |||||
| Input | Power | 80KVA
72KW |
100KVA
90KW |
120KVA
108KW |
160KVA
144KW |
180KVA
144KW |
200KVA
160KW |
||||
| No. of phases | 3 phase 4 wires + PE | ||||||||||
| Rated voltage | 380/400/415Vac | ||||||||||
| Voltage range | 208~478Vac | ||||||||||
| Frequency range | 45-55Hz a 50Hz / 56-66Hz to 60Hz (auto sensing) | ||||||||||
| Power factor | ≥0.99 | ||||||||||
| THDi | ≤2%(100% non linear load) | ||||||||||
| By-pass voltage range | Max voltage.: 220Vac:+25% (optional +5%,+10%,+15% ) 230Vac:+20% (optional +10%,+15% ) 240Vac:+15% (optional +10% ) |
||||||||||
| Min voltage.: -45% (optional -20%、-30%) | |||||||||||
| Frequency protection range: ±10% | |||||||||||
| Generator input | Supported | ||||||||||
| Output | No. of phases | 3 phase 4 wires + PE | |||||||||
| Rated voltage | 380/400/415Vac | ||||||||||
| Power factor | 0.9 | 0.8 | |||||||||
| Voltage accuracy | ±1% | ||||||||||
| Frequency | Line | ±1%、±2%、±4%、±5%、±10% rated frequency (optional) | |||||||||
| Battery | (50/60±0.1%)Hz | ||||||||||
| Crest Factor | 3:1 | ||||||||||
| THD | ≤1% linear load – ≤3% non linear load | ||||||||||
| Efficiency | ≥96,5% | ≥97,5% | |||||||||
| Battery | Quantity | Dynamic 16-18-20pcs (configurable) | |||||||||
| Autonomy | 10’ standard with embedded battery | ||||||||||
| Overload | Normal op.: 110% 60′ – 125% 10′ – 150% 1′ – >150% switch to bypass | ||||||||||
| Self-check | Automatic self test at switch on | ||||||||||
| Display | LCD: Voltage IN/OUT – Frequency IN/OUT – Load – Battery Voltage
Operating Temp. – Overload – Failure – Alarms |
||||||||||
| Interface | USB – RS485 – Clean Contacts- Intelligent slot | ||||||||||
| Communication | SNMP (optional) – MODBUS (optional) – RELAY card (optional) | ||||||||||
| Operating temperature | Operating: 0° + 40° / Storage: -25° + 55° | ||||||||||
| Dimensions (DxWxH) mm | 828x500x868 | 828x750x868 | 828x1000x868 | ||||||||
| Number of units | 2 | 3 | 4 | ||||||||
